- 1 What is the best way to mic a choir?
- 2 How do you mic a choir for live performance?
- 3 How do you EQ choir?
- 4 How loud is a choir?
- 5 How do you mic a small choir?
- 6 How do you record a large choir?
- 7 What is a phantom power source?
- 8 What frequency should vocals be at?
- 9 Where should vocals sit in a mix?
- 10 How loud should my vocals be in a mix?
- 11 How do I record my mic?
- 12 Can you record music with just a microphone?
What is the best way to mic a choir?
Seven simple rules:
- Place the choir microphones properly.
- Use the minimum number of microphones.
- Turn down unused mics.
- Let the choir naturally mix itself.
- Don’t over-amplify the choir.
- Try not to sing at the mic.
- Sing in a natural voice.
How do you mic a choir for live performance?
When placing mics to pick up the choir, a critical factor is gain before feedback. To get enough gain, you must to mic the choir much closer than you would for recording. Place the mics about 18 inches in front of the first row of singers, and about 18 inches above the head height of the back row (Figure 1).
How do you EQ choir?
EQ Vocals: The Five Primary Areas of Modification
- 01 Drop the Very Low. Roll off below 100 Hz using a High Pass Filter.
- 02 Tenderize Harsh Vocals. To remove harshness from a vocal, apply a narrow bandwidth cut within the 1 KHz to 4KHz range.
- 03 Brighten the Vocals. Apply a gentle boost using a wide frequency band above 6 KHz.
- 04 Smooth it Out.
- 05 Bring out the Bass.
How loud is a choir?
Taking 3 dB as a distinguishable level difference for most listeners, a choir voice range profile should show a range of at least 15 dB between the softest (pp) and loudest (ff) notes over a wide frequency range (about 2 octaves per choir section).
How do you mic a small choir?
The easiest way to mic a small choir (25 voices or fewer) is to use a single stereo mic or a pair of mics. I’ve used coincident (two capsules aligned side by side) stereo mics similar to the RODE NT4 small -diaphragm condenser or the Telefunken AR70 large-diaphragm condenser.
How do you record a large choir?
10 Tips for Recording a Choir
- Find the Right Space.
- Arrange the Choir for Optimal Blend.
- Pick Your Favorite Stereo Mic Setup.
- Use Small-diaphragm Condensers for Overheads.
- Use the Three-Foot Rule for Mic Placement.
- Use Room Mics for Ambiance.
- Use Spot Mics When Necessary.
- Leave Plenty of Headroom.
What is a phantom power source?
Phantom Power is a term given to the process of delivering DC (Direct Current) to microphones requiring electric power to drive active circuitry. Condenser microphones such as Shure’s KSM range all have active circuitry and require phantom power.
What frequency should vocals be at?
Male vocals will tend to have their fundamental frequencies between 100–300 Hz, while the fundamental frequencies of a female vocal will usually fall between 200–400 Hz.
Where should vocals sit in a mix?
The vocals should sit well without any automation, but then towards the end of the mix I’ll turn the speakers down and listen at really low levels, and go through the mix 10 or 15 seconds at a time and ride up all the words and phrases that get lost, really do a ton of little micro rides on the vocal.
How loud should my vocals be in a mix?
Every vocal is different and every song is different as well. But generally speaking, lead vocal should be moderately loud or the loudest element next to your drums in your mix.
How do I record my mic?
To record your voice in Sound Recorder, your computer must have a built-in or external microphone attached.
- Press “Windows-W” to open Settings, enter “sound” into the search field and then select “Sound” from the results.
- Select the “Recording” tab and confirm that a microphone is connected to the computer.
Can you record music with just a microphone?
You can use the built-in mic on your laptop to record audio, and in some cases, it doesn’t sound half bad. However, you definitely can ‘t expect to capture the best quality audio this way. A Shure SM57 is a relatively cost-effective option at about $100 to $120, and can be used on just about any instrument.